Side Table With Drawer Plans Included

Learn how to build this cute side table with plenty of storage for your blankets, books, or games.

I've got a brand new side tabular array project to share and I am thrilled with how it turned out! I'm partnering with my friends over at Build Something to bring you the printable plans for this project, which yous tin download on their site. This side table has plenty of storage and also plenty of space for you to display your books or dwelling decor. I'thousand sharing the photo tutorial below and I've as well put together a video of the entire build.

*this postal service contains affiliate links

Why Build Your Ain Article of furniture?

The beauty of building your own furniture is that it costs FAR less to build it than buy it. In fact, I was just recently talking nearly this and said that I build piece of furniture to fit my attention span. Seriously! If a piece of article of furniture lasts for years and years, great! Only if my tastes suddenly change and I decide I want to build something new for a room, it doesn't break the bank like information technology would if I were Ownership new furniture.

Another huge benefit? If something needs to be repaired, you can likely fix information technology very easily. For instance, let's say your oldest son'southward friend gets locked nether your youngest son'south bed and decides to kick his way out and breaks to door off. You lot can fix it! Trust me, that helped me calm down A LOT when that incident happened. Imagine if I had bought that captain's bed and had to try to discover a replacement door?!

Scout: How To Build A Side Tabular array With Storage

Step By Step Tutorial: How To Build A Side Tabular array

I congenital this side table using rough-cut knotty alder. This means that I had to mill downward the lumber to dimensional sizing. I drew up the plans for this project to reverberate dimensional lumber sizing (for example: a 2×2 is 1 1/two″ 10 one 1/2″) to make it easier to follow.

In using knotty alder, information technology also meant that I had quite a few large knots in the woods. I filled them all with epoxy that I tinted with gray paint powder. Information technology fills them in really nicely and provides a more finished look.

Build The Side Panels and Shelf

To become started, you'll want to build the side panels and the shelf. Cut all of the wood to the dimensions listed in the printable plans. Drill 3/iv″ pocket holes into the boards. Mucilage upward the joints and clamp together, then secure with 1 ane/4″ pocket screws. I cut the console boards a bit long considering it'due south difficult to ensure they are assembled perfectly flush with each other. I used my Adaptive Cut Organisation to square up one end, then turned the panel around to trim it downward to size. I followed these aforementioned steps to build the shelf of the tabular array every bit well.

Drill three/4″ pocket holes into all four sides of the side panels and each end of the shelf.

Build the Back Panel And Drawer Front

Drill iii/4″ pocket holes in the boards that brand upward the drawer front and dorsum console of the side table. Gum and clamp the boards together, and then secure with 1 i/4″ pocket screws.

Assemble The Tabular array Base of operations

With the panels built, information technology is time to get together the table base. Drill one 1/2″ pocket holes into the 17 1/two″ 2×2 pieces. Glue and clamp these pieces to the top and bottom edges of the side panels. Secure in identify with 1 1/4″ pocket screws. Attach the legs with wood gum and 2 one/two″ pocket screws besides as 1 1/4″ pocket screws where the panels meet the legs.

Attach the stretchers to the front and back sides of the table base, 1 i/2″ upwardly from the bottom of the legs. Use wood glue and 1 1/4″ pocket screws to attach.

Glue and clamp the solid back panel of the table in place. Secure with ane 1/iv″ pocket screws.

Build The Table Superlative

For the table top, I ripped 6/four knotty alder down to 5 i/2″ widths. vi/4 lumber is ane 1/ii″ thick, so ripping them to 5 ane/2″ broad makes them the equivalent of ane×6 boards. Again, I cut these boards a piffling long to trim up afterward. I glued upward the edges of the boards and clamped them together. Be careful not to over tighten the clamps when gluing up the tiptop to prevent bowing. I let the glue cure overnight, and then trimmed the table top downwardly to size on my Adaptive Cutting Organization.

Attach The Table Top

I used desktop fasteners to attach the table height to the base of operations. I used three on each side and traced around the smaller side with a pencil. Using a 3/4″ forstner bit on my drill, I drilled a pigsty approximately 1/viii″ deep. The fastener should be flush with the top of the base. I fastened the fasteners with 1 1/4″ wood screws. I centered the tabular array top over the base and then clamped it in identify. I then attached information technology through the other end of the fastener with 1 one/4″ wood screws.

Build Drawer Boxes

I ripped my plywood pieces to 7″ wide and then cut them down to length on my miter saw. I drilled 3/4″ pocket holes into the front and back pieces of the drawer box. I glued and clamped the pieces together, so secured them with 1 1/four″ pocket screws. I cutting ane/4″ plywood to match the dimensions of the drawer box, then fastened it with wood glue and 3/four″ narrow crown staples. Yous can also use brad nails for this.

Installing Drawer Slides

Install the drawer slides using the Kreg drawer slide jig. For this table, residuum the drawer slide jigs on the bottom stretcher and clench into place. Drill 1/16″ pilot holes into the drawer slide holes and attach with the included screws.

For the drawer box, heart the drawer slides on each side of the drawer box. Drill airplane pilot holes and then attach with the included screws.

Adhere The Drawer Forepart

To adhere the drawer front end, utilize the Kreg chiffonier hardware jig to drill the holes for the handle/pull you will be attaching. Gear up the jig and so the pigsty placement is the same as your hardware. Drill the holes into the drawer front only. Middle the drawer front over the drawer box. Playing cards work great to fix an even gap all of the way around. Bulldoze 1 one/four″ wood screws through the holes and into the drawer box. Pull the drawer out and drill pilot holes into the inside of the drawer box close to all iv corners. Attach the drawer forepart with 1 ane/four″ wood screws. Cease drilling the iii/xvi″ holes through the first two holes drilled. Adhere the drawer handle/pull.

Finish the project every bit desired

This project can be finished any way y'all like. I am choosing to go out it natural for the moment until I build the matching coffee table. I also need a niggling time to really decide merely how I want to cease it.

I'll be honest, I'm kind of loving the black hardware against the natural woods. I may get pretty light on the stop with this. What practise you recall?

Make sure that you lot visit Build Something to go the plans for this project! If you want to add together it to your projection list, be certain to pin it for later on!

DISCLOSURE: I was provided products and/or bounty for this post. All opinions and ideas are 100% my own.

rangelanings.blogspot.com

Source: https://addicted2diy.com/how-to-build-a-side-table-with-storage/